Bushing dies better?
New to reloading and getting ready to reload for 6.5 prc. Got a forster coax and trying to decide which dies to get. I have lapua brass. I want to buy the best and not regret what im getting. Any advice?
View ArticleOld recipe deemed Unsafe in new manuals. Suggestions?
Back in the 80's I had a recipe with IMR4350 from Lyman's 46th edition that gave me less than 1/2", 5 shots at 100 yards. According to the book, it was at the Max, but no pressure signs. Used this...
View ArticleRifle primer question!
Anybody have a tried and true favorite on Primers? I need Large Magnum rifle primers, and suggestions, and maybe elaborate why? What is the difference between regular magnums and match grade?...
View ArticleLooking for assistance with load development
Looking for assistance with load development for both Hunting and Target Ruger Precision 6.5 Creedmoor - 24"Barrel - 1: 8 twist - AimSport Silencer Lapua Brass - small Primer Pocket What Primer /...
View Article7.82 Lazzeroni Patriot dies
Hi all, My brother-in-law, a heck of a nice guy, recently gifted me with a Savage 116LZ chambered in 7.82 (.308) Patriot. I knew the brass was exorbitantly expensive, but I was a bit shocked to find...
View ArticleAbsolute Hammer load data
I think this will work. @GLTaylor has been compiling load data from folks working up loads with the new Absolute Hammer bullets. Thanks to him for his hard work. I figured I would post it in a place...
View Article190 gr. Cutting edge subsonic 300 blk out experience?
As the title states wondering if anyone has any real life experience with these loaded as subs? I have a Rem bolt gun so not really concerned about cycling and I have starter data from the company....
View ArticleSS pins - a note of caution
I always have the LabRadar running while shooting at our club. A shooter a few benches away asked if I would shoot his 300WBY to determine the velocity of his reloads. My equipment is set up for a left...
View ArticlePRIMERS: Magnum or Standard for 6.5 PRC
I am shooting a Bergara Wilderness Ridge 6.5 PRC. (24" barrel / 1:8 twist) and I am trying to work up some loads. Question? For those that load this caliber; do you load with magnum or standard...
View ArticleBullet seating depths
Can bullet seating depth change the velocity of your load and point of impact?
View Article6.5 prc powders
I am going to work up some 6.5 prc loads and need some advice. 4 of the bullets I’m working all recommended rl 26 2 of the 4 actually said it was their most accurate tested. Problem is I’m out of 26...
View Article4831 SC in 6.5 PRC
Anybody have any data on this combo? I recently bought 8 lbs because it’s what I could get for a decent price. I know it’s touted for it’s accuracy so I don’t mind giving up speed. I have a bit of...
View ArticleWinchester brass good enough or not worth it?
Found a good deal on some Winchester brass and there’s a couple bags available at my sportsman’s warehouse. I normally use Norma brass but it is extremely hard to come by right now. Anyone have...
View ArticleWhat is this case?
Picked this up at my range last weekend. Shown next to a 9mm case for reference. Would have just guessed it was aluminum cased 9mm, but it's a two piece sliding design with a significantly reduced...
View Article338 wsm
I finaly got my 338-325 WSM done and all I can say is WOW! If anyone else has one I'd like to share load data. I used a 700 long action, Lilja 28" barrel 10 twist in a sendero stock. I used Quickload...
View Article22 creedmoor
Anyone willing to post or pm me so starting reloading data for 22 creedmoor 77gr 80gr 90gr and 95gr bullets. I have RL26 rl23 h4831 h4831sc. Thanks doug
View ArticleWhere Are the Bullets?
Lots of powder dropping but where are the bullets? I’ve been trying to find 178 grain ELD-X and some Berger’s and nothing. Anyone finding any bullets online? I’ve been checking to no avail.
View ArticleWhat is the best/fastest case trimmer
I have a Lyman universal case trimmer that has sucked from day one. I'm ready to upgrade and would like to hear a few opinions on an accurate and fast case trimmer. Any suggestions? Thanks
View Article
More Pages to Explore .....